ALL JENSEN DOOR SYSTEMS' DOORS (EXCEPT THOSE DOORS EXPRESSLY EXCLUDED FROM THIS WARRANTY BY THE MANUFACTURER) ARE WARRANTED FOR ONE YEAR FROM DATE OF SHIPMENT BY THE MANUFACTURER TO BE FREE OF DEFECTS WHICH WOULD RENDER SAID DOOR(S) UNSERVICEABLE OR UNFIT FOR THE ORDINARY, RECOMMENDED USE. THE MANUFACTURER DOES NOT WARRANT PERFORMANCE OF ANY FINISH OR FINISHING MATERIALS. FACTORY FINISHES CARRY ONLY LIMITED WARRANTY FOR MATERIALS AND WORKMANSHIP AT TIME OF DELIVERY.
WARRANTY
CONDITIONS:
AT THE TIME SHIPMENT IS RECEIVED, ALL DOORS MUST BE INSPECTED AND
ANY NOTICEABLE DEFECTS REPORTED WITHIN 30 DAYS TO THE MANUFACTURE. IF
A DEFECT IS DISCOVERED OR OCCURS AFTER THE DOOR IS HUNG, WRITTEN NOTICE
MUST ALSO BE SENT TO THE MANUFACTURER WITHIN ONE YEAR (1-YEAR) FROM DATE
OF SHIPMENT. MANUFACTURER, AT HIS OPTION, UPON WRITTEN NOTIFICATION OF
SAID DEFECT(S) WILL: (1) REPAIR DEFECTIVE DOOR(S); OR (2) REPLACE DOOR(S),
WHICH SHALL NOT INCLUDE ANY COSTS FOR TAKING DOWN DEFECTIVE DOOR(S), FINISHING
OR HANGING OF NEW DOORS OR (3) REFUND THE CURRENT OWNER AN AMOUNT NOT
TO EXCEED THE ORIGINAL PURCHASE PRICE PAID TO THE MANUFACTURER BY THE
ORIGINAL PURCHASER.
LIMITATIONS
AND EXCLUSIONS:
1. JENSEN DOOR SYSTEMS DOES NOT WARRANT DOOR(S) THAT HAVE NOT BEEN
PROPERLY INSTALLED
OR FINISHED. CUTTING INTO THE MORTISE AND TENON JOINT WILL VOID WARANTY.
IMMEDIATELY
AFTER CUTTING FINISHING, BUT BEFORE HANGING, THE ENTIRE DOOR, INCLUDING
TOP AND
BOTTOM EDGES, MUST RECEIVE AN APPLICATION OF PRIMER OR SEALER AND TWO
COATS OF A
GOOD GRAD OF PAINT, VARNISH OR LACQUER.
2. THE APPEARANCE OF FIELD FINISHED DOORS OR FACTORY FINISHES BEYOND TIME
OF DELIVERY IS
NOT UNDER WARRANTY.
3. WARP SHALL NOT BE CONSIDERED A DEFECT UNLESS IT EXCEEDS 3/8 INCH. WARP
IS ANY
DISTORTION IN THE DOOR ITSELF AND SHALL INCLUDED BOW, CUP, AND TWIST.
MEASUREMENT
OF THE AMOUNT OF WARP IN A DOORS WILL BE PLACING A STRAIGHTEDGE ON THE
SUSPECTED
CONCAVE FACE OF THE DOOR AT ANY ANGLE (i.e.:HORIZONTALLY, VERTICALLY,
DIAGONALLY),
WITH THE DOOR IN AN INSTALLED POSITION. THE MEASUREMENT OF BOW, CUP AND
TWIST
SHALL BE MADE AT THE POINT OF MAXIMUM DISTANCE BETWEEN THE BOTTOM OF THE
STRAIGHTEDGE AND THE FACE OF THE DOOR.
4. WARRANTY AGAINST WARP SHALL EXCLUDE ALL DOORS THAT ARE: (1) 1 3/8"
THICK: WIDER THAN
3'0" OR HIGHER THAN 7'0"; (2) 1 3/4" WIDER THAN 3'6"
OR HIGHER THAN 8'0"; (3) ALL DOORS
IMPROPERLY INSTALLED; (4) ANY 1 3/8" THICK DOOR USED AS AN EXTERIOR
DOOR.
5. PANEL SHRINKAGE IS NOT CONSIDERED A DEFECT COVERED BY THIS WARRANTY.
6. ALL VISIBLE DEFECTS MUST BE REPORTED BEFORE THE DOOR IS HUNG.
7. DOORS WITH NO OVERHANG OR DOORS EXPOSED TO EXTREME OR UNUSUAL WEATHER
CONDITIONS ARE NOT COVERED BY WARRANTY.
8. REFINISHED DOORS MAY NOT MATCH BROCHURE OR SAMPLE PANELS IN COLOR.
9. ALL DOORS WITH PANELS OVER 14" INCH WIDTH ARE EXCLUDED FROM THE
WARRANTY.
10. WOOD SURFACE CHECKS, MITRE AND OTHER WOOD JOINT SHRINKAGE SHALL NOT
BE
A DEFECT UNLESS SUCH EXCEEDS .025" INCH WIDTH.
MANUFACTURER'S RESPONSIBILITY:
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE FOREGOING, AND THE
MANUFACTURER'S RESPONSIBILITY UNDER THIS WARRANTY IS AS STATED HEREIN.
MANUFACTURER SHALL NOT BE LIABLE FOR CONSEQUENTIAL, INDIRECT OR INCIDENTAL
DAMAGES OR FOR ANY AMOUNT IN EXCESS OF THE MANUFACTURER'S PRICE FOR THE
DOOR(S) INVOLVED, WHETHER THE CLAIM IS FOR BREACH OF WARRANTY OR NEGLIGENCE.
